Find the moment of inertia (a) of a thin uniform rod relative to the axis which is perpendicular to the rod and passes through its end, if the mass of the rod is m and its length l; (b) of a thin uniform rectangular plate relative to the axis passing perpendicular to the plane of the plate through one of its vertices, if the sides of the plate are equal to a and b, and its mass is m.
(a) For the rod, I = m l² / 3. (b) For the plate, I = m (a² + b²) / 3. Your sliders: rod ; plate .
Problem statement
Problem 1.224. Find the moment of inertia (a) of a thin uniform rod relative to the axis which is perpendicular to the rod and passes through its end, if the mass of the rod is m and its length l; (b) of a thin uniform rectangular plate relative to the axis passing perpendicular to the plane of the plate through one of its vertices, if the sides of the plate are equal to a and b, and its mass is m.
Interpretation. In part (a) the rod lies in a plane and the axis is a straight line at right angles to the rod, going through one end. In part (b) the plate is flat, and the axis is a straight line at right angles to the plate, going through one of its corners. In both parts the body is uniform: equal parts have equal mass.
We assume sample numbers so that the page can draw the bodies: m = 2 kg for both, l = 1.0 m for the rod, and a = 0.6 m and b = 0.4 m for the plate. All are sliders, and the results are written with symbols, so they hold for any values.
Symbols: m is the mass, l the length of the rod, a and b the sides of the plate, I the moment of inertia about the axis, x the distance of a piece from the axis, and r the distance of a piece from the axis in the plate.
The big idea in plain words
The moment of inertia is a sum over all the little pieces of the body: each piece of mass dm is multiplied by the square of its distance from the axis, and all the products are added. A piece far from the axis counts much more than a piece near it, because the distance is squared.
The picture is a 3D view that you can turn with the mouse. The vertical line is the axis. The amber piece is a probe that moves over the body, and the page prints its dm, its distance and its dI. Use the tabs above the picture to switch between the rod and the plate.
The solution in each frame
Frame of the body
Distances are measured from the axis, and the axis stays fixed in the body. This is the frame used below.
Frame through the centre of mass
The moment of inertia about the axis through the centre of mass is smaller. The parallel axis rule links the two: I = I(cm) + m d², where d is the distance between the parallel axes. It is used below as a check.
The solution step by step
Part (a), the rod
Step 1, one piece. Cut the rod into thin strips of width dx. Put x along the rod, with x = 0 at the end where the axis passes. A strip at distance x has the mass dm = (m / l) dx, because the rod is uniform and its mass per length is m / l.
Step 2, its share. The strip is at distance x from the axis, so its moment of inertia is
Step 3, add up. Add the shares from x = 0 to x = l. The sum of x² dx from 0 to l is l³/3 (this is the area under the curve x² and it is the only calculus step, since the integrand is a simple power):
Step 4, numbers. With your sliders m = kg and l = m, I = kg·m². For the sample, I = 2 × 1² / 3 = 0.667 kg·m².
Part (b), the plate
Step 1, one piece. Put the axis through the corner O, and put x along the side a and y along the side b. A small piece at (x, y) is at distance r from the axis, and r² = x² + y², because the axis is at right angles to the plate and the piece lies in the plate.
Step 2, its share. dI = r² dm = x² dm + y² dm. So the total is the sum of two sums: I = Σ x² dm + Σ y² dm.
Step 3, add up with the rod result. For Σ x² dm, group the pieces into thin strips parallel to the side b. Every piece in a strip has the same x, so the strips behave like the strips of the rod in part (a): the plate in x is just a rod of length a and mass m. Hence Σ x² dm = m a² / 3. In the same way Σ y² dm = m b² / 3. Therefore
No new integral is needed: part (a) is used twice.
Step 4, numbers. With your sliders m = kg, a = m and b = m, the two parts are and kg·m², and I = kg·m². For the sample, I = 2 × (0.36 + 0.16) / 3 = 0.347 kg·m².
A separate sum does not use the formulas. For the rod it cuts the rod into 4000 equal strips and adds (m / 4000) x² for each strip. For the plate it cuts the plate into a 120 by 120 grid and adds (m / 14400)(x² + y²) for each cell. For your numbers the rod sum is kg·m² (formula , difference ) and the plate sum is kg·m² (formula , difference ).
Other methods
Parallel axis rule. For the rod, I about the centre is m l² / 12, and the axis through the end is d = l/2 away, so I = m l²/12 + m (l/2)² = m l²/12 + m l²/4 = m l²/3. Here I(cm) = kg·m² and I(cm) + m d² = kg·m². For the plate, I about the centre is m (a² + b²) / 12, and the corner is d = √(a² + b²) / 2 from the centre, so I = m (a² + b²)/12 + m (a² + b²)/4 = m (a² + b²)/3. Here I(cm) = kg·m² and I(cm) + m d² = kg·m².
Graph. For the rod, the first graph plots dI per unit length, (m / l) x², against x. The area under it is I. The plate graphs show how I grows with each side and with the mass.
Calculus. It is needed once, for the sum of x² dx. Everything else is algebra.
Reusing the rod result for the plate is the fastest method. The grid sum is the independent check.
What each slider changes
| Control | What it changes |
|---|---|
| Mass m | The mass of every piece (dm), I, I about the centre, the probe values and all graphs, in both parts. |
| Length l (part a, header slider too) | The length of the rod in the 3D view, the strips, I, the probe values and the graphs. |
| Side a (part b, header slider too) | The plate in the 3D view, I, the two parts of I, the probe path and the graphs. |
| Side b (part b) | The plate in the 3D view, I, the two parts of I, the probe path and the graphs. |
Parameters
| Quantity | Symbol | Value used |
|---|---|---|
| Mass | m | kg |
| Length of the rod | l | m |
| Sides of the plate | a, b | m, m |
| I of the rod | m l² / 3 | kg·m² |
| I of the plate | m (a² + b²) / 3 | kg·m² |
Exam traps
- Using m l² / 12. That is the value about the centre. For the axis through the end the value is m l² / 3, four times larger.
- Taking the distance of every piece as l. Each piece has its own distance x, and the squares are added.
- Using m (a² + b²) / 12 for the plate. That is about the centre. For the axis through a vertex it is m (a² + b²) / 3.
- Adding the moments of inertia of the two sides as if they were rods about their ends in different planes. The correct step is r² = x² + y² for each piece, and then the two sums.
- Forgetting the units. The moment of inertia has the units kg·m², and the sides must be in metres.
- Mixing up the axis. Here the axis is at right angles to the plate. An axis along a side of the plate gives m b²/3 or m a²/3, not the full sum.